J'ai depuis quelques heures un problème avec le disque dur de mon Mac
Mini PPC (qui tourne etch):
Apr 4 14:06:01 localhost kernel: ide-pmac lost interrupt, dma status:
8400
Apr 4 14:06:01 localhost kernel: hda: lost interrupt
Apr 4 14:06:01 localhost kernel: hda: dma_intr: status=0x58
{ DriveReady SeekComplete DataRequest }
Apr 4 14:06:01 localhost kernel: ide: failed opcode was: unknown
Apr 4 14:06:01 localhost kernel: hda: status timeout: status=0xd0
{ Busy }
Apr 4 14:06:01 localhost kernel: ide: failed opcode was: unknown
Apr 4 14:06:01 localhost kernel: hda: DMA disabled
Apr 4 14:06:01 localhost kernel: hdb: DMA disabled
Apr 4 14:06:01 localhost kernel: hda: drive not ready for command
Apr 4 14:06:09 localhost kernel: ide0: reset: success
Jusqu'à ce que le reset ne fonctionne pas et la partition est remontée
en read-only et qu'il crashe.
Voici ce que donne smartmontools:
mjollnir:/home/carl# smartctl -a /dev/hda
smartctl version 5.36 [powerpc-unknown-linux-gnu] Copyright (C) 2002-6
Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 4200.2 Series
Device Model: ST9808210A
Serial Number: 3LF0VK9G
Firmware Version: 3.04
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Fri Apr 4 18:26:42 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging
support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five
errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 36 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 08 dc d2 4c e0 00 00:24:15.035 READ SECTOR(S) EXT
24 00 08 04 90 4f e0 00 00:24:15.026 READ SECTOR(S) EXT
24 00 00 3e 13 5b e0 00 00:24:14.988 READ SECTOR(S) EXT
24 00 08 74 10 3a e0 00 00:24:14.985 READ SECTOR(S) EXT
24 00 08 64 c6 33 e0 00 00:24:14.982 READ SECTOR(S) EXT
Error 35 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 08 dc d2 4c e0 00 00:24:07.699 READ SECTOR(S) EXT
24 00 08 54 9c 4f e0 00 00:24:07.688 READ SECTOR(S) EXT
24 00 08 6c 7b 4f e0 00 00:24:07.673 READ SECTOR(S) EXT
24 00 08 74 a8 4f e0 00 00:24:07.667 READ SECTOR(S) EXT
24 00 08 7c 9e 4f e0 00 00:24:07.784 READ SECTOR(S) EXT
Error 34 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
24 00 08 dc d2 4c e0 00 00:24:00.153 READ SECTOR(S) EXT
24 00 08 24 8c 4f e0 00 00:24:00.146 READ SECTOR(S) EXT
24 00 08 54 8a 4f e0 00 00:24:00.143 READ SECTOR(S) EXT
24 00 08 8c 7d 4f e0 00 00:24:00.129 READ SECTOR(S) EXT
24 00 08 dc ac 4f e0 00 00:24:00.127 READ SECTOR(S) EXT
Error 33 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719
Error 32 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 7e 8e a5 e0 Error: UNC at LBA = 0x00a58e7e = 10849918
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 1f 67 8e a5 e0 00 00:01:53.438 READ DMA EXT
25 00 20 66 8e a5 e0 00 00:01:52.545 READ DMA EXT
25 00 08 5e 8e a5 e0 00 00:01:52.456 READ DMA EXT
25 00 20 0e 8e a5 e0 00 00:01:52.456 READ DMA EXT
25 00 08 06 8e a5 e0 00 00:01:52.456 READ DMA EXT
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
J'ai lu sur http://lists.debian.org/debian-powerpc/2005/07/msg00279.html
(ou
http://groups.google.co.uk/group/linux.debian.ports.powerpc/browse_frm/thread/f12646d58f5f7b23/cfae90a4cc189071%23cfae90a4cc189071%5D)
que c'était peut-être un problème avec UMDA/4, mais je n'ai jamais eu
cela auparavant.
Quelqu'un peut me dépanner?
Merci,
--
Carl
--
Lisez la FAQ de la liste avant de poser une question :
http://wiki.debian.org/DebFrFrenchLists
Vous pouvez aussi ajouter le mot ``spam'' dans vos champs "From" et
"Reply-To:"
To UNSUBSCRIBE, email to debian-user-french-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Cette action est irreversible, confirmez la suppression du commentaire ?
Signaler le commentaire
Veuillez sélectionner un problème
Nudité
Violence
Harcèlement
Fraude
Vente illégale
Discours haineux
Terrorisme
Autre
Sylvain Sauvage
Carl Devos, vendredi 4 avril 2008, 20:15:37 CEST
Bonjour,
âjour,
J'ai depuis quelques heures un problème avec le disque dur de mon Mac Mini PPC (qui tourne etch): [â¦] 1 Raw_Read_Error_Rate 0x000f 049 043 034 Pre-fail Always - 28191970
J'ai depuis quelques heures un problème avec le disque dur de mon Mac
Mini PPC (qui tourne etch):
[â¦]
1 Raw_Read_Error_Rate 0x000f 049 043 034 Pre-fail Always
- 28191970
J'ai depuis quelques heures un problème avec le disque dur de mon Mac Mini PPC (qui tourne etch): [â¦] 1 Raw_Read_Error_Rate 0x000f 049 043 034 Pre-fail Always - 28191970